ArcWear performs vertical flame testing for textiles in accordance with ASTM D which is used in ASTM F, ASTM F, and NFPA We will report. 23 Jul Some updates have been made to ASTM D Standard Test Method for Flame Resistance of Textiles (Vertical Test) commonly used in flame. ASTM D Test Method for Flame Resistance of Textiles. (Vertical Test). • Pass criteria: max char length of 10 cm. • After-flame of not more than 2 seconds.

Author: Voodoogami Shaktijind
Country: Chile
Language: English (Spanish)
Genre: Literature
Published (Last): 13 July 2015
Pages: 162
PDF File Size: 2.66 Mb
ePub File Size: 17.31 Mb
ISBN: 624-9-26045-527-1
Downloads: 9141
Price: Free* [*Free Regsitration Required]
Uploader: Toktilar

Afterflame is the number of seconds during which there is a visible flame remaining astm d6413 the fabric. ASTM D is used to determine flame resistance of fabrics used astm d6413 protect against both electric arc and flash fire hazards. As a minimum, the test samples used should be as homogeneous as possible, that are drawn from the material astm d6413 which the disparate test results are obtained, and that are assigned randomly in equal numbers to each laboratory for testing.

ICS Number Code Link to Active This link will always route to the current Active version of the standard.

Asgm astm d6413 to the astm d6413, afterflame, afterglow and char astm d6413 are measured: Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The purpose of this test is to determine whether a fabric will continue to burn after the source of ignition is removed. The cut edge of the fabric on the bottom is exposed to a controlled methane flame for 12 seconds as seen in the image above, left.

Combining values from the two systems may result in non-conformance with the standard.

The occurrence of melting or dripping, if any, astm d6413 also recorded. It is the responsibility of the user of this standard to establish appropriate safety and health practices ashm determine the applicability of astm d6413 limitations prior to use.

ASTM D6413: Vertical Flame Test for Flame Resistance of Textiles

Tyndale performs astm d6413 safety auditing on Tyndale garment fabrics. The between-laboratory precision of this test method has not been established.

Save my name, email, and website in this browser for the wstm time Astm d6413 comment. Char Length is the length in inches of fabric destroyed by the flame. Work Item s – proposed revisions of this standard.

NFPA 2112 – ASTM D6413: Vertical flame test method

We are Astm d6413 to Protect workers, and understand that our astm d6413 to testing is the only s6413 to ensure that our garments perform as expected — every time! Other materials with established test values may be used for this purpose. Refer to Section 14 for single-laboratory precision. Historical Version s – view previous versions of standard.

ASTM D – 99 Standard Test Method for Flame Resistance of Textiles (Vertical Test)

The test results from the two laboratories should be compared using a statistical test for unpaired data, astj astm d6413 probability level chosen prior to the testing series. Your email address will not be published. July 10, at 9: Garments that meet these standards are used to comply with: The values stated in each system may not be exact equivalents; therefore, each system shall be used independently astm d6413 the other.

Notify me of new posts by email.

Nfpa – astm d vertical flame test method

D64113 a astm d6413 is found, either its cause must be found and corrected, or future test results must be adjusted in consideration on the known bias. Notify me of follow-up comments by email.

Five tests are performed and the results are averaged astm d6413 reported as the final test result. Adopted from Federal Test Standard No. Leave a Reply Cancel reply Your email address astm d6413 not be published. Astm d6413 is the number of seconds during which there is a visible glow remaining on the fabric. This is the defining test method for compliance with OSHA The ASTM D test method is utilized to evaluate the flame resistance of every production lot of fabric used in Tyndale-branded clothing.